1.3 Inch 128×64 IIC I2C OLED Blue Display Module For Arduino
This OLED display module is small, only 1.3″ inch diagonal, it is made of 128×64 individual blue OLED pixels, each one is turn on or off by the controller chip. It has white backlight and can work without backlight, OLED display is higher compared to that of LCD display, you will like the miniature for its crispness. This module uses I2C to communicate with microcontroller such as Arduino.
In stock
₨ 860
In stock
1.3 Inch OLED IIC Serial Blue White OLED Display Module 128X64 I2C SSD1306 12864 LCD Screen Board For Arduino
The 1.3″ OLED display is a perfect ultra-small display. It is an OLED monochrome 128×64 dot matrix display module with SPI Interface. The characteristics of this 1.3 inch oled display module are high brightness, high contrast ratio, self-emission, slim outline, wide temperature range, wide viewing angle, and low power consumption.
It is compatible with any 3.3v-5V microcontroller, such as the Arduino.
Features of 1.3″ oled display:
- Interface: i2c
- Text Color: Blue
- Diagonal Screen Size: 1.3 inch
- Working Voltage: 3.3 – 5V
- Resolution: 128 x 64
- Driver IC: SSD1106
- Input Voltage: 3.3V/5V
- Pins:
- VCC: (Power)
- GND: (Ground)
- SCL: (Clock)
- SDA: (Data Cable)
- PCB Size: 35.4mm x 33.5 mm
- Display Area: 29.42mm x 14.7 mm
Package List:
- 1 x 1.3 inch 128×64 i2c OLED – Blue
Useful Links:
Adafruit library for 1.3 inch oled
- Color: Blue LED
- Resolution: 128×64
- Power: 0.06W
- Wide power supply range: DC 3V-5V
- Temperature: -30°C to 70°C
- Dimension: 29.28 x 27.1 mm (LW)
- Compatible with 3.3V and 5V control chip I / O level
- OLED internal drive chip: SSD136
- I2C interfaces
- 128*64 Resolution
- 160° viewing angle
Related products
- Audio & Visual, Audio & Sound
Piezo Buzzer 95db High-decibel 3-24V Electronic Buzzer Beep Alarm Intermittent Continuous Beep
Audio & Visual, Audio & SoundPiezo Buzzer 95db High-decibel 3-24V Electronic Buzzer Beep Alarm Intermittent Continuous Beep
- Color: Black
- Alarm Diameter:22mm/0.86″
- Alarm Height:10mm/0.39”
- 2 Mounting Holes distance:30mm/1.18″
- 2 Wires length:90mm/3.54″
- Buzzer Type: Piezoelectric
- Sound Pressure Level 95 dB
- Rate Voltage: 12V DC
- Operating Voltage: 3 – 24V
- Max Current Rating 10mA
- Frequency 3900±500Hz
- Drive Method: Drive Circuit Built in Mounting Holes
SKU: 0685 - Audio & Visual, LCD & Display
2.4 Inch ILI9341 Touchscreen TFT LCD Display Screen Shield Module For Arduino UNO R3 Board
Audio & Visual, LCD & Display2.4 Inch ILI9341 Touchscreen TFT LCD Display Screen Shield Module For Arduino UNO R3 Board
- Color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
- Composed of a color TFT-LCD panel, driver IC, FPC and a back light unit. The module display area contains 320 x 240 pixels.
- The screen uses analog pins A0-A4 for LCD control and touch screen operations, which are in the same position on the UNO and the Mega, so the touch screen should work without any modification.
- The shield comes equipped with a micro SD card reader for easy access to use a software-based SPI library.
- Compatible with Arduino UNO R3 Mega2560 DUE.
SKU: 0177 - Audio & Visual, LCD & Display
16×2 LCD Display 1602 Character Display for Arduino – Blue
- Operating Voltage is 4.7V to 5.3V
- Current consumption is 1mA without backlight
- Alphanumeric LCD display module, meaning can display alphabets and numbers
- Consists of two rows and each row can print 16 characters.
- Each character is build by a 5×8 pixel box
- Can work on both 8-bit and 4-bit mode
- It can also display any custom generated characters
- Backlight Color: Blue
SKU: 0804 - Audio & Visual, LCD & Display
4 Bits TM1637 Digital Tube LED 7 Segments Display Module
The module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.
SKU: 1057
