Piezo Buzzer 95db High-decibel 3-24V Electronic Buzzer Beep Alarm Intermittent Continuous Beep
- Color: Black
- Alarm Diameter:22mm/0.86″
- Alarm Height:10mm/0.39”
- 2 Mounting Holes distance:30mm/1.18″
- 2 Wires length:90mm/3.54″
- Buzzer Type: Piezoelectric
- Sound Pressure Level 95 dB
- Rate Voltage: 12V DC
- Operating Voltage: 3 – 24V
- Max Current Rating 10mA
- Frequency 3900±500Hz
- Drive Method: Drive Circuit Built in Mounting Holes
In stock
₨ 120
In stock
Related products
-
Audio & Visual, LCD & Display
8×2 LCD Display 0802 Character Display – Yellow Green
WH0802A1 is an 8 character by 2 lines 8×2 character LCD display. This 8×2 LCD module is available in various LCD panel colors including gray, yellow/green and blue LCD options. 0802 LCD module is built in with ST7066 controller (or equivalent). WH0802A1 model has different interfaces available, it’s default 6800 4/8-bit parallel 6800 interface, also it’s optional SPI and I2C by using RW1063 IC.
SKU: 0956 -
Audio & Visual, LCD & Display
12864 128X64 KS0108 Dots Graphic LCD Display Module (Blue Color Backlight)
Audio & Visual, LCD & Display12864 128X64 KS0108 Dots Graphic LCD Display Module (Blue Color Backlight)
The 12864B Graphic LCD module is a 128×64 pixel LCD display with a blue backlight and white foreground. The display is fully programmable and can display a combination of both graphics and text. It can operate in both parallel and serial (SPI) modes which can be configured by the external pin PSB. In SPI mode only 3 data pins are required to drive this display.
SKU: 0957 -
Audio & Visual, LCD & Display
2.4 Inch ILI9341 Touchscreen TFT LCD Display Screen Shield Module For Arduino UNO R3 Board
-20%
Audio & Visual, LCD & Display2.4 Inch ILI9341 Touchscreen TFT LCD Display Screen Shield Module For Arduino UNO R3 Board
- Color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
- Composed of a color TFT-LCD panel, driver IC, FPC and a back light unit. The module display area contains 320 x 240 pixels.
- The screen uses analog pins A0-A4 for LCD control and touch screen operations, which are in the same position on the UNO and the Mega, so the touch screen should work without any modification.
- The shield comes equipped with a micro SD card reader for easy access to use a software-based SPI library.
- Compatible with Arduino UNO R3 Mega2560 DUE.
SKU: 0177 -
Audio & Visual, LCD & Display
4 Bits TM1637 Digital Tube LED 7 Segments Display Module
The module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.
SKU: 1057 -
Audio & Visual, LCD & Display
0.96 Inch 128×64 IIC I2C OLED Blue Display Module For Arduino
This OLED display module is small, only 0.96″ inch diagonal, it is made of 128×64 individual blue OLED pixels, each one is turn on or off by the controller chip. It has white backlight and can work without backlight, OLED display is higher compared to that of LCD display, you will like the miniature for its crispness. This module uses I2C to communicate with microcontroller such as Arduino.
SKU: 0537
